Видео

Just picked one up for $100! SR 1433, made in 97-98

I’m sorry……But, those 5 extra minutes paid Dividends. Thanks for the video. I have subscribed to your channel .

Not the fuel line with the filter, but the return line. Some return lines have a connector on the end withing the fuel tank. Is the connector required? Thanks

This guy was a dick, waisted 7min of my life. I’ll just plug the line into one 50% chance. There

How to make a 10sec video into a bunch of worthless words

Thank-you

whos on first, what line is the return line, wait port. cover your right eye and squeeze bulb, thats the port line. Sir please identify the gas line that has the filter, then identify the return line/port line, do u see how confusing that is. Is one bigger? is one on the leftside or right side top port. Very confusing and way too long.

I crushed the diode didnt know what it was lol my mower still goes but battery dies now even when off

What size allen key did it call for ?

Thanks for info. Not trying to criticize but that's a 2 cycle

Pump the bulb. Put your finger over the holes One will suck the other will blow.

What if u don’t have a suck line

Hey, really good video. I enjoyed the info. I'm about to go adjust my Snapper right now.

Okay so now I’m confused which line the fuel filter goes on🥺

How do you know what size you need . I got one and it was a little too small . It won’t screw in . Thanks !

MTD made a lot of variations of lawn tractors over the years. I wish you would post what year your lawn tractor is cause they're not all made the same.

Thank you for clarifying how far the lines extend into the gas tank.

I have this inverter but it's 48v . Can it be converted to 24v

great advice

Many thanks ur a G

Good luck finding a engine

My life is too short for this delay.

Long vid

My Troy Bilt is doing the same, cables, burning/smoking melting, I've ordered some new cables, my neighbor made new cables for it last time, I rode it back to my yard.. and then I seen the smoke again. That was the last time I'd done anything with it, hoping I can get it running again

Great job 👍!!!

I think it's supposed to spin

This is a terrible explanation, you are to far away to see what the hell you are talking about

Good idea. Get your iron hotter!

What if the purge bulb is separate from the carb?

I think its 2cycle

Nice video. But, I was advised that the feed/suction line to filter was the thin line and the thicker line was the return line. I have a 1995 32cc craftman. ?

Ffwd to 4:40 for the answer.. you're welcome

You talk too much. Just give us the information, thank you.

Thank you so much. Great video. Now I know

Thank you. As soon as you started to explain by pushing the bulb i knew what to do. Perfect explanation thank you

Lmao, just straight-pipe it.

This video helps a lot. Thanks.

Fixed mine! Thank you!!!!

Thanks, I was getting crazy because it stopped heating suddenly and I couldn't figure out why

For novices: You could have clarified in 1/4 of the time or 3 minutes. With your accent, I could understand "return", but could not understand the second port until I read others comments to mean, "Suction" and not "Substance" or any other word. It would have been better understood if you spelled out the word, "S-u-c-t-i-o-n".

Long time. How is it going?

Total waste of my time as this didn’t prove anything. The battery may have been good but the fluids were drained from it. 15 minutes and it still doesn’t provide any results worth watching.

😅

What is the benefit of multiple charge controller..

This worked for me, too. Thanks!

This is great! I've done that to determine suction too. Always good idea to replace primer blub too as it's made of the same materials as line I'm sure.

Perfect fixed my grandpa's ancient iron, now I get to keep using a piece of history :)

Much appreciated

With 24 volt solar panels does it charge the battery twice as fast. Any advantages and disadvantages? Thank you

Okay, I'll say it for everyone. Great video however it was 5 minutes to long. Wow can you drag out a 1-minute video to 6 minutes. Maybe I'm looking at it wrong, maybe this video is for someone who doesn't have a clue on how to work on equipment. With that being said after reading the comments I believe that's what's happening. Okay great video for them. Now I see and believe that you should make the video 5 minutes longer so they can understand what they don't know. Great video